Runtime
software Optimizer
MC Pro
OPTIMIZE THE MOST COMPLEX SPEAKER LAYOUTS
On top of the standard AES-EBU / Analog combinations, the MC Processor is also available in 3 other flavors to support high-channel-count installations.
The MC-HCC range includes MADI, AES67 and Dante variants.
Based on the common market standard, our compatibility scheme provides network audio capabilities to our MC users offering compatibility with all standards.
ALL IN ONE PRECISE MONITORING SOLUTION_
Trinnov Audio’s Integrated Monitoring Solutions gather in a single processor all the required tools for accurate audio monitoring over the most complex speaker layouts.
I played the reference recordings without the Trinnov, and the difference was night and day. To say three jaws were hitting the floor is no exaggeration. The timing of bass and kick drums was brought sharply into focus and lost any vagueness and approximation. Gone was any bass bloat and bloom. The imaging dramatically improved, with a very firm focused phantom center image, the tonality of good mixes sounded even better and more equal. Reverbs and delays were sharper and more apparent. The dynamics and timing, in general, were much tighter.
Mike Aiton (re-recording mixer)
(Resolution Magazine, June 2018)
MODULAR PLATFORM_
The Trinnov MC Processor is an expandable hardware platform that can handle any multichannel format and any loudspeaker layout from 2.0 to 22.2.
MC Processors are designed to host optional software modules such as the Optimizer and/or the SmartMeter.
EVOLUTIVE ARCHITECTURE_
Both AES8 and Analog8 standard configurations allow for 8 simultaneous I/O and 8 processing channels.
Optional AES8 and/or ADA4 boards can be added to provide up to 16 simultaneous I/O channels.
Alternatively, AES inputs can be configured for input source switching of3 groups of 8 inputs (3xAES8).
COMPREHENSIVE PROCESSING_
Comprehensive 64-bit floating point processing tools are included on each processor platform: routing and mixing matrices, manual FIR filters, parametric EQs, graphic EQs, gains, trims, peak, and RMS meters.
Manual delays, bass management, 4-way active crossovers, inputs formats, noise generators, polarity control, editable Submix matrices, monitor controller, dynamic range controller.
4 WAY INTELLIGENT CROSSOVER ALIGNMENT_
Individual driver and system measurements are acquired and analyzed, including the impulse response, delays, and gains.
Trinnov’s unique crossover calibration engine computes the ideal filters, finding the best compromise to improve flatness, directivity, and attack in the overlapping frequency region.
MC CONFIGURATIONS & OPTIONS
AVAILABLE CONFIGURATIONS
- MC-ANA8
8 analog I/O processor platform. Can be expanded to 16 analogs I/O and 16 AES I/O. - MC-ANA16:
16 analog I/O processor platform. Can be expanded with 16 AES I/O. - MC-AES8:
8 AES I/O processor platform. Can be expanded to 16 AES I/O and 16 analogs I/O. - MC-AES16:
16 AES I/O processor platform. Can be upgraded with 16 analogs I/O.
MC-HCC LINE-UP
- MC-HCC-MADI*:
- High Channel Count 64 channels IN / OUT via MADI.
- MADI optical or MADI coaxial (BNC)
- MC-HCC-AES 67*:
- High Channel Count 64 channels IN / OUT on network
- Ravenna based, fully AES67 / SMPTE 2110-30 compatible (also with Dante in its AES67 compatible mode)
- MC-HCC-Dante*:
- High Channel Count 64 channels IN /OUT on network
- Audinate Dante based, with AES67 compatibility mode.* no analog, no AES-EBU inputs/outputs
AVAILABLE HARDWARE OPTIONS
- ADA4 Expansion Boards:
- One ADA4 Expansion Board adds 4 Analog I/O Channels of pristine AD / DA Conversion.
- A total of 4ADA4 Expansion Boards can be installed on a single processor.
- AES8 Expansion Boards:
- One AES8 Expansion Board adds 8 AES I/O Channels. Alternatively, AES inputs can be configured for input source switching of 3 groups of 8 inputs (non-simultaneous AES input channels).
- A maximum of 2 AES8 Expansion Boards can be installed on a single processor.
AVAILABLE SOFTWARE OPTION
SMART METER
Most typical loudness real-time loudness meters require to measure a project from beginning to end without rollbacks or time jumps to obtain its Integrated Loudness level. Even if pausing is possible with most instruments, this method is not ideal.
Trinnov’s unique time code-aware SmartMeter takes loudness metering to a new dimension. The measurement automatically starts and pauses following the playback system, continuously providing consistent values, whether the operator jogs, shuttles or rewinds through the project.
TRINNOV PROCESSING
- Several layers of 31 bands Graphic EQ, FIR EQ, gains, polarity and delays available for every channel
- Total delay given in meters/milliseconds/frames for the listening point and adjustable global delay for accurate Lip Sync; Front / Surround / Top balance
REMOTE & LOCAL PARAMETERS
- Source Selection : 4 Cues/TB/LB, 6 Cues/TB/LB, 8 Cues/TB/LB, 8 Cues/TB/LB
- Monitor Selection : upon programmable presets & profiles
- Switching Matrix : any physical input, mix bus or Optimizer® output to any physical output
- Summing Matrix : (Mono/ST) 12 in / 8 bus, 12 in / 12 bus, 18 in / 16 bus, 18 in / 16 bus
AUDIO SPECIFICATIONS
- ADC Resolution / Sampling Rate: 24 Bits/96 Khz
- DAC Resolution / Sampling Rate: 24 Bits/96Khz
- A/D Signal-To-Noise Ratio: 119 Db (A-Weighted)
- D/A Signal-To-Noise Ratio: 118 Db (A-Weighted)
- Analog Input Impedance: Balanced: 20 Kohms
- Reference Level: +18Dbu @ 0Dbfs (Balanced)
- Clock / Jitter: (Jitter Attenuation > 50 Db Above 100Hz)
PHYSICAL CHARACTERISTICS
Dedicated linear power supply with a toroidal transformer on the analog audio circuit.
Dedicated PSU / switch-mode power supply on the digital audio circuit.
Power supply: 240V AC / 50-60 Hz. Option: 130V AC
Consumption: 90 W max.Weight: ∼14.5kg Chassis: 2U
